Parts for Kenmore Models 7215A REV B

Dishwasher bottom door gasket (bottom gasket)

This gasket goes on the bottom of the dishwasher door to create a tight seal between the tub and the outer edge of the door. If the gasket is cracked or broken, it will need to be replaced to keep water from leaking out on to the floor. The gasket is approximately 23” long and is a genuine OEM part. It is recommended that once you have installed the gasket to leave the door closed for a few hours to make sure the gasket is properly sealed.

Easy Part #:: EAP9495545

Availability:: In Stock

Price:: $19.45

Chrome drip bowl - 6" (use 5303280336)

The 6-inch drip bowl sits under the burner to catch anything that may spill over to make cleaning up spills quick. This chrome drip bowl is compatible with electric ranges that utilize plug-in surface burners. This bowl measures approximately 8-inches in diameter. If your drip bowl becomes damaged or rusted it is best to replace the drip bowl to avoid any grease or spill from dripping down inside the range. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP437596

Availability:: In Stock

Price:: $6.00

Refrigerator door shelf bin

This refrigerator door shelf bin is an attachment for your refrigerator door to hold small items in your fridge, such as condiments. The bin attaches to the inside of the refrigerator door to hold food items on the door shelves. The shelf may need to be replaced if it is warped or broken. The shelf is white in color and is sold individually.

Easy Part #:: EAP429873

Availability:: In Stock

Price:: $45.93

Door bin - clear

This bin can be moved according to space needed. It holds items on the door of your refrigerator. NOTE: This bin is only available in clear plastic now.

Easy Part #:: EAP430122

Availability:: In Stock

Price:: $68.99

Thermal cut-off kit (cutoff-tml)

This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. This genuine OEM kit also includes flat heaters with jumper wires. Make sure to disconnect the power source to the dryer before beginning this repair.

Easy Part #:: EAP334299

Availability:: In Stock

Price:: $41.40

Door balance link kit (link, door balance)

The door balance kit helps support the weight of the dishwasher door while it opens and closes. If the spring to the door is damaged/broken or the door is not opening and closing properly you will need to replace this part. This door kit includes 2 door balance links and 2 door balance mounts with wheels for the left and right side of the door. This is a genuine OEM part.

Easy Part #:: EAP972325

Availability:: In Stock

Price:: $27.90

Dryer cycling thermostat (cycling thermostat (limit: 155-25))

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock

Price:: $23.85

Bake element (oven bake element. The terminals are male quarter inch spade connectors. The wires push onto the heating elements connectors.)

This partially open-style bake element comes with ¼-inch push-on terminals and is located on the bottom of the oven. This bake element provides heat for baking. If your oven is too hot, not heating evenly, the element is not heating, or has little to no heat when baking, you may need to replace your bake element. You can use a multi meter to test the bake element for electrical continuity to see if you need to replace it. This is a genuine OEM part. Please remember to disconnect the power to the range before starting your repair.

Easy Part #:: EAP249247

Availability:: In Stock

Price:: $52.85

Lower rack assembly - grey (lower dishwasher dishrack assembly.)

This part is a genuine OEM part. This white lower dish rack assembly comes with eight light-gray rollers for easy access. The dish rack is approximately 21 inches wide x 22 inches deep. The dish rack holds dishes in place during the dish washing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, you will need to replace the part. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly.

Easy Part #:: EAP17219605

Availability:: No Longer Available

M series new style coil kit (dryer valve coil kit)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334310

Availability:: In Stock

Price:: $26.40

Rear drum support roller kit (support)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP347627

Availability:: In Stock

Price:: $13.37

D-shaped knob clip (u clip)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Easy Part #:: EAP268493

Availability:: No Longer Available

Meat drawer rail - right side (drawer support rail - right side)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.

Easy Part #:: EAP430126

Availability:: In Stock

Price:: $41.79

Rear drum bearing kit (shaft)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:: EAP459829

Availability:: In Stock

Price:: $52.07

Upper crisper drawer cover - glass not included

This cover holds up the top crisper drawer, and has drawer glides molded in it. This upper crisper drawer cover is a manufacturer-approved replacement part for your refrigerator. It has drawer glides molded into the frame but this part does not include the glass cover. To replace this part, lift out the glass cover and snap out the drawer frame. Snap this new frame cover into place and replace the glass.